890ZV SOFC Test Load
Model 890ZV는 프로그래머블 전자 부하, 연료 및 온도 제어, 데이터 수집 기능을 하나로 통합한 벤치탑형 시험 시스템입니다.
내장 전원 공급 장치를 탑재하여, 연구·실험실·교육 환경에서의 소형 단일 셀 SOFC 시험에 특히 적합합니다.
890ZV는 비용 효율성과 컴팩트한 크기를 중심으로 최적화되었으며, 추가 하드웨어 기능과 Scribner의 FuelCell® 소프트웨어를 함께 제공합니다.
본 시스템은 일반적으로 SOFC 연료전지, 적합한 퍼니스(Furnace), 그리고 **연료 관리 유닛(Fuel Management Unit)**과 함께 사용됩니다.
또한, 890 시리즈는 Scribner 885 통합형 연료전지 포텐쇼스탯과의 호환됩니다.
Features
2단 전류 범위 전자 부하
5 / 25 A
최대 10 V, 50 W
셀 및 퍼니스 온도 램핑 제어
단계적 온도 상승 및 제어 가능
질량 유량 컨트롤러 제어 신호 제공
메인 MFC 2대
추가 MFC 최대 5대 지원
Current Interrupt 방식
실시간 셀 저항 측정
IR-Free 전압 연속 모니터링
전체 셀 전압 + 2채널 고임피던스 레퍼런스 전극 입력
하프셀 데이터 측정 지원
옵션 내장 임피던스 분석기
전기화학 임피던스 분광(EIS)
실시간 고주파 저항(HFR) 연속 측정
비절연(Non-Isolated) 셀 호환
셀 메인 단자 및 센스 입력 안정성 확보
내부 제어기 3채널
애노드 가습기
캐소드 가습기
셀 온도 제어
전류 / 전압 / 전력 제어 모드 지원
압력 센서 또는 알람용 접점 입력 3채널
저전압 출력 신호
퍼지 가스 밸브 제어
알람 상태 표시
RS-485 디지털 인터페이스
지원되는 외부 장비 연동 가능
완전한 시험 스테이션 구성 시 유의 사항
890ZV는 맞춤형 또는 서드파티 연료 관리 유닛이 필요합니다.
Options
| 885 PStat Potentiostat | Fuel Cell Potentionstat |
| 881 Frequency Resistance Analyzer (FRA) | FRA for High Frequency Resistance (HFR) in impedance measurement from 1 mHz to 10 kHz |
| 892e Data Acquisition Expansion System | Additional 8 voltage and 8 temperature inputs |
| Interface Box | An interface box may be purchased for non-integrated fuel system designs |
| Gas Mixing | Gas mixing for reformate simulation or impurities/poisons studies |
Specifications
| Electronic Load: | |
| Maximum Load Current (2 ranges): | 5 A, 25 A |
| Maximum Load Voltage: | 10 V |
| Maximum Load Power: | 50 W |
| Minimum Load Resistance: | 3.3 V power supply used to allow zero load voltage at full current with up to 3.2 V drop in cell wiring |
| Current Resolution: | 1 mA |
| Current Accuracy: | 0.3% of full scale current of selected range |
| Voltage Measurement and Data Acquisition: | |
| Maximum Whole Cell Voltage: | 10.000 V |
| Maximum Reference Electrode Voltage: | 9.999 V |
| Whole Cell Sense Voltage Input Resistance: | » 35 kΩ |
| Reference Electrode Input Resistance: | » 109Ω |
| Voltage Resolution: | 1 mV |
| Voltage Accuracy: | +/-3 mV +/-0.3% of reading |
| Voltage and Current Data Update Rate: | 100 Hz |
| Fuel Interface: | |
| Outputs for anode, cathode flow controllers: | Two, Analog (0-5 V) |
| Outputs for reformate flow controllers: | Five, Analog (0-5 V) (optional) |
| Alarm Inputs: | Six: Three for gas pressures, three auxiliary |
| Alarm Outputs: | One, 5 V logic |
| Fuel Solenoid Control: | One, 5 V output (external relay needed, included with interface box) |
| Temperature Controllers: | |
| Quantity: | Three (Anode, Cathode and Cell / Furnace) |
| Type: | On/off 5 V output (external SSR required) |
| Set and Report Accuracy: | +0.25% of span, +1 least significant digit |
| Sensor Type: | Thermocouple, Type K Standard, T or S optional |
| Impedance Measurement: | |
| Interface for internal or external analyzers: | Voltage and current output channels with variable DC bias rejection, generator input channel with selectable attenuation |
| Internal Impedance Analyzer Type: | Single sine, two gain/phase measurement channels, one generator output channel |
| Internal Analyzer Frequency Range: | 1 mHz to 10 kHz |
| Measurement Channels: | Three: whole cell plus two half cell vs. reference electrode |
| Environment: | |
| Operating Temperature: | 0-40 °C ambient; all specs given for 25 °C ambient |
| Power Source: | 100-240 VAC, 50/60 Hz (auto select) |
| Size: | 3U std rack mount, 19” W x 5.25" H x 21" D |
| Safety Features: | Automatic shutdown and N2 purge with under voltage, over-current, over-temperature, loss of supply pressures, low water, furnace over-temperature, communications failure or external alarm. Manual Emergency Stop switch for manual operator shutdown. |